BTT EBB42 Can Toolhead Board

30,00 

Availability: In stock and ready to ship!

EBB42 v1.2 without max amplifier from BTT.

Flashed by us with canboot and klipper.

It was flashed with can bus speed 500000.

How to wire the board?

How do I connect the Board?

If you have a BTT Octopus there is a guide to connect this can toolhead directly to the RJ11 of the board using a bridge mode.

Although we recommend to leave it alone (it’s too much complicated) and use a middleman such as U2C that we also sell. The U2c is like an interpeter that will convert and read the CAN data. U2c connects via USB-C to the RPI and the can toolhead board can be connected to the U2C via 4 cables only.

This meand that you will reduce your cable harness from 17 cables to 4 cables only!

How to identify uuid?

~/klippy-env/bin/python ~/klipper/scripts/canbus_query.py can0

Diagram Pin

Example of config file ?

## EBB config by Lab4450
## for Voron 3D printers

[mcu EBBCan]
# run the following command to locate the uuid and replace below   ~/klippy-env/bin/python ~/klipper/scripts/canbus_query.py can0
canbus_uuid: 0e0d81e4210c

## TEMPERATURE SENSOR OVER THE CANBOARD
[temperature_sensor EBBCan]
sensor_type: temperature_mcu
sensor_mcu: EBBCan
min_temp: 0
max_temp: 100

## EXTRUDER
[extruder]
step_pin: EBBCan:PD0
dir_pin: !EBBCan:PD1
enable_pin: !EBBCan:PD2
full_steps_per_rotation: 200         # Set to 200 for LDO 1.8° stepper motor, and set to 400 for OMC(StepperOnline) 0.9° stepper motor
rotation_distance: 22.23             # See calibrating rotation_distance on extruders doc
gear_ratio: 50:10                                                   
microsteps: 32
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: EBBCan: PB13            #PB13 FOR V1.2 OR PA2 FOR V1.1
sensor_pin: EBBCan: PA3
sensor_type: PT1000   #our pt1000 works directly. there is no need of max amplifier. just place a jumper in pt1000
pullup_resistor: 2200             
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 350

[tmc2209 extruder]
uart_pin: EBBCan:PA15
run_current: 0.600    # for LDO 36STH20-1004AHG
stealthchop_threshold: 0
sense_resistor: 0.110

## PART COOLING FAN
[fan]
pin: EBBCan: PA0

## EXTRUDER FAN
[heater_fan hotend_fan]
pin: EBBCan:PA1
heater: extruder
max_power: 1.0
kick_start_time: 0.5
heater: extruder
heater_temp: 50.0

## RGBW double-check if it's not duplicated with stealthburner_leds.cfg
[neopixel sb_leds]
pin: EBBCan:PD3
chain_count: 3
color_order: GRBW
initial_RED: 1.0
initial_GREEN: 0.0
initial_BLUE: 1.0
initial_WHITE: 0.0

## PROBE double-check if it's not duplicated with servo klicky_servo
[probe]
pin: EBBCan:PB9

## ACCELEROMETER
[adxl345]
cs_pin: EBBCan:PB12
spi_software_sclk_pin: EBBCan:PB10
spi_software_mosi_pin: EBBCan:PB11
spi_software_miso_pin: EBBCan:PB2
axes_map: x,y,z

Do I need to flash anything?

No. We sell all of our boards pre flashed.

Customers also bought

Shopping Cart
BTT EBB42 Can Toolhead Board
30,00 

Availability: In stock and ready to ship!

OFFICIAL RESELLER

 

Check the CNC and CF products in here!